manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

28  USB FUNCTION CONTROLLER (USB)

S1C33L26 TECHNICAL MANUAL

 

Seiko Epson Corporation 

28-51

Perform  the  setup  so  that  combination  of  the  EndpointNumber  and  the  INxOUT  does  not  overlap  with  those  of 
other endpoints.

D7 

ISO

 

Sets the isochronous mode.

D6 

ISO_CRCmode

 

According to USB spec, a packet must be discarded when CRC error occurs in isochronous transaction. 
When this bit is set, a packet with CRC error is not discarded. This bit is valid when ISO bit (D7) is set.

D[5:0] 

Reserved

EPaStartAdrs_H (EPa FIFO Start Address HIGH)
EPaStartAdrs_L (EPa FIFO Start Address LOW)

Register name Address

Bit

Name

Setting

Init. R/W

Remarks

EPaStartAdrs_H
(EPa FIFO start
address high)

0x300c70

(8 bits)

D7–4 –

–

–

–

0 when being read.

D3–0 EPaStartAdrs[11:8]

Endpoint EPa start address

0x0 R/W

EPaStartAdrs_L
(EPa FIFO start
address low)

0x300c71

(8 bits)

D7–2 EPaStartAdrs[7:2]

Endpoint EPa start address

0x0 R/W

D1–0 –

–

–

–

0 when being read.

EPaStartAdrs[11:2]

 

Sets the start address of the FIFO area allocated to the endpoint EPa. 

 

The area that is allocated to the endpoint EPa is from the address set by the EPaStartAdrs and to the ad-
dress one byte before the one set by the EPbStartAdrs.

 

After setting the StartAdrs of all endpoints, be sure to set the AllFIFO_Clr bit of the EPnControl regis-
ter to 1 to clear all FIFOs.

 

If the EPaMaxSize of the endpoint EPa is larger than the area specified in here, the macro does not op-
erate normally. 

 

Set the total of the FIFO area secured for all endpoints does not exceed the total capacity of the built-in 
RAM. 

 

Allocate the FIFO area to the endpoints in the order from the lower order address to higher order ad-
dress like EP0, EPa, EPb, EPc, EPd. 

 

The FIFO of the endpoint EP0 is allocated from the address 0 to up to the size specified as the Max-
PacketSize of the endpoint EP0 set in the EP0MaxSize register. Allocate the succeeding area for other 
endpoints. 

 

Since the FIFO capacity is 1K bytes, do not let the EPd end address exceed 0x3ff. And do not let the 
EPaStartAdrs exceed the setting value of the EPbStartAdrs.

EPbStartAdrs_H (EPb FIFO Start Address HIGH)
EPbStartAdrs_L (EPb FIFO Start Address LOW)

Register name Address

Bit

Name

Setting

Init. R/W

Remarks

EPbStartAdrs_H
(EPb FIFO start
address high)

0x300c72

(8 bits)

D7–4 –

–

–

–

0 when being read.

D3–0 EPbStartAdrs[11:8]

Endpoint EPb start address

0x0 R/W

EPbStartAdrs_L
(EPb FIFO start
address low)

0x300c73

(8 bits)

D7–2 EPbStartAdrs[7:2]

Endpoint EPb start address

0x0 R/W

D1–0 –

–

–

–

0 when being read.

EPbStartAdrs[11:2]

 

Sets the start address of the FIFO area allocated to the endpoint EPb. 

 

The area that is allocated to the endpoint EPb is from the address set by the EPbStartAdrs and to the ad-
dress one byte before the one set by the EPcStartAdrs.

 

After setting the StartAdrs of all endpoints, be sure to set the AllFIFO_Clr bit of the EPnControl regis-
ter to 1 to clear all FIFOs.

 

If the EPbMaxSize of the endpoint EPb is larger than the area specified in here, the macro does not op-
erate normally. 

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Baader Planetarium Steeldrive II Manual preview
Steeldrive II
Brand: Baader Planetarium Pages: 7
Lamtec FA1 Quick Reference preview
FA1
Brand: Lamtec Pages: 22
Velleman KA01 Manual preview
KA01
Brand: Velleman Pages: 12
Sonos Controller CR100 Quick Setup Instructions Manual preview
Controller CR100
Brand: Sonos Pages: 12
Vageo RT-1 Manual preview
RT-1
Brand: Vageo Pages: 2
DirectConnect VC70DSW Instructions preview
VC70DSW
Brand: DirectConnect Pages: 2
Danfoss 087H3803 Installation Manual preview
087H3803
Brand: Danfoss Pages: 20
B&R Automation PC 810 User Manual preview
Automation PC 810
Brand: B&R Pages: 428
Universal Remote Control total control MRX-10 Owner'S Manual preview
total control MRX-10
Brand: Universal Remote Control Pages: 16
Genasun GVB-8-WP Series Manual preview
GVB-8-WP Series
Brand: Genasun Pages: 8
Hamamatsu C7557 Instruction Manual preview
C7557
Brand: Hamamatsu Pages: 50
Cypress AN77960 Manual preview
AN77960
Brand: Cypress Pages: 13
ADLINK Technology cPCI-7252 User Manual preview
cPCI-7252
Brand: ADLINK Technology Pages: 54
Aqua Lung Legend LX Second Stage Technical Maintenance Manual preview
Legend LX Second Stage
Brand: Aqua Lung Pages: 18
A.O. Smith INTELLI-VENT Troubleshooting Manual preview
INTELLI-VENT
Brand: A.O. Smith Pages: 46
Phocos CIS05-2L User Manual preview
CIS05-2L
Brand: Phocos Pages: 2
AudioCodes Mediant 4000B SBC Hardware Installation Manual preview
Mediant 4000B SBC
Brand: AudioCodes Pages: 60
Atmel AVR461 Quick Start Manual preview
AVR461
Brand: Atmel Pages: 16

Brands by name

Popular brands

Load more brands