manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

REVISION HISTORY

Code No.

Page

Contents

411900101

19-7

USIL: Receive data mask function
(Old)  Receive data mask function (master mode)
 

The USIL in SPI master mode provides a receive data mask (data retransmission) function. ...

 

... For normal data transfer, set SMSKEN to 0 (default) to disable the receive data mask function.

(New) Deleted

19-11

USIL: Data transfer in UART mode - Data reception
(Old)  If the subsequent receive data is written to the receive data buffer when URDIF is 1, an overrun er-

ror occurs.

(New) If the next reception is completed ... an overrun error occurs (at the time stop bit has been received).
USIL: Data receiving timing chart (UART mode)
Modified Figure 19.5.1.2

19-12

USIL: Data transmission timing chart (SPI mode)
Modified Figure 19.5.2.1
USIL: Data transfer in SPI mode - Data reception
(Old)  If the subsequent receive data is written to the receive data buffer when SRDIF is 1, an overrun er-

ror occurs.

(New) While SRDIF is set to 1, ... overrun error occurs at the time the first bit of the third byte is fetched).

19-13

USIL: Data receiving timing chart (SPI mode)
Modified Figure 19.5.2.2

19-14, 19-15 USIL: I

2

C master data transmission timing chart

Modified Figure 19.5.3.2

19-15, 19-16 USIL: Sending slave address and transfer direction bit

(Old)  ... In 10-bit mode, data is sent twice under software control. ... 
 

To send a 10-bit address, execute this procedure twice as shown in Figure 19.5.3.4. ...

(New) ... In 10-bit mode, data is sent twice or three times under software control. ... 
 

Modified Figure 19.5.3.4

 

... To send a 10-bit address, execute this procedure twice or three times as shown in Figure 19.5.3.4. ...

19-17, 19-18 USIL: I

2

C master data receiving timing chart

Modified Figure 19.5.3.9

19-19

USIL: Control method in I

2

C slave mode 

(Old)  ... After an interrupt occurs, ... (ISSTA[2:0]/USIL_ISIF register) to check the operation finished.
(New) ... After an interrupt occurs, ... This also automatically reset ISSTA[2:0] to 0x0.

19-20

USIL: I

2

C slave data transmission timing chart

Modified Figure 19.5.3.12

19-22

USIL: I

2

C slave data receiving timing chart

Modified Figure 19.5.3.14

19-23

USIL: Data Transmission in LCD SPI Mode
(Old)  The LSBSY flag indicates the USIL status ... the LCD SPI controller is operating or at standby.
(New) The LSBSY flag indicates the USIL status ... LSDMOD[1:0]/USIL_LSDCFG register has completed.

19-24

USIL: Figure 19.5.4.1
(Old)  Data Transmission Timing Chart (LCD SPI mode)
(New) Data Transmission Timing Chart (LCD SPI mode, 16-bit data format)
USIL: Data Transfer in LCD Parallel Mode - Data write
(Old)  To write data to the LCD driver/panel ... the command bit status (LPCMD/USIL_LPCFG register).
 

The LCD parallel interface asserts the chip enable and write signals and outputs the buffer data ...

 

The command bit status is output from the USIL_DI pin.

 

The transmitter circuit includes ...

(New) To write data to the LCD driver/panel ... the command bit status (LPCMD/USIL_LPCFG register).
 

The command bit must be set before ... the USIL_DI pin immediately after it is written to the register.

 

The LCD parallel interface asserts the chip enable signal and outputs the buffer data ...

 

The transmitter circuit includes ...

USIL: Data-Write Timing Chart (LCD parallel mode)
Modified Figure 19.5.5.1

19-25, 19-48 USIL: Data Transfer in LCD Parallel Mode - Data read

(Old)  The LCD parallel interface asserts the chip enable and read signals ... via the USIL_DI pin.
(New) Set the command bit ... output from the USIL_DI pin immediately after it is written to the register.

19-27

USIL: Receive errors - Overrun error
(Old)  Overrun error Overrun error (UART, SPI, I

2

C modes)

 

If data is received before the previously received data in the receive data buffer has not been read, ...

 

The overrun error flag is reset to 0 by writing 1.

(New) Overrun error (UART, SPI, I

2

C master/slave modes)

 

UART mode

 

An overrun error occurs if the next reception is completed when URDIF is 1 and the receive data ...

 

I

2

C master/slave mode

 

... To reset an overrun error, write 1 to IMEIF/ISEIF and then read the receive data buffer (USIL_RD 
register) twice.

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Hable One Starting Manual preview
One
Brand: Hable Pages: 3
Vega VEGAMET 141 Operating Instructions Manual preview
VEGAMET 141
Brand: Vega Pages: 20
Zander Aachen SCB Series Operating Instructions Manual preview
SCB Series
Brand: Zander Aachen Pages: 44
Zamel Extra Free ROB-01/12-24V Manual Instruction preview
Extra Free ROB-01/12-24V
Brand: Zamel Pages: 2
Technische Alternative UVR 63H Operation And Installation Manual preview
UVR 63H
Brand: Technische Alternative Pages: 68
McIntosh MHT200 Owner'S Manual preview
MHT200
Brand: McIntosh Pages: 68
Cypress CY3250-PLC20QFN Quick Start Manual preview
CY3250-PLC20QFN
Brand: Cypress Pages: 2
Harsen GU641A Operation Manual preview
GU641A
Brand: Harsen Pages: 55
Wabtec Ricon 55914 Installation Instructions preview
Ricon 55914
Brand: Wabtec Pages: 5
Samson TROVIS 6495 Series Mounting And Operating Instructions preview
TROVIS 6495 Series
Brand: Samson Pages: 156
YASKAWA Sigma-7Siec Hardware Manual preview
Sigma-7Siec
Brand: YASKAWA Pages: 38
Danfoss PVE 4 Series Technical Information preview
PVE 4 Series
Brand: Danfoss Pages: 56
3Ware 720-0104-00 Manual preview
720-0104-00
Brand: 3Ware Pages: 50
SATA air regulator belt plus Operating Instructions Manual preview
air regulator belt plus
Brand: SATA Pages: 158
ICP DAS USA Compact Embedded Controller LinPAC-8x41 Hardware User Manual preview
Compact Embedded Controller LinPAC-8x41
Brand: ICP DAS USA Pages: 13
AUMA SAEx 07.2 Manual preview
SAEx 07.2
Brand: AUMA Pages: 88
Kohzu Precision MontBlanc KOSMOS CRUX-D User Manual preview
MontBlanc KOSMOS CRUX-D
Brand: Kohzu Precision Pages: 74
Oriental motor EZ limo ESMC-A2 Operating Manual preview
EZ limo ESMC-A2
Brand: Oriental motor Pages: 94

Brands by name

Popular brands

Load more brands