manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

20  GENERAL-PURPOSE SERIAL INTERFACE (FSIO)

S1C33L26 TECHNICAL MANUAL

 

Seiko Epson Corporation 

20-21

Notes:  •  When using the IrDA interface, set the internal division ratio of the serial interface to 1/16 (DI-

VMD/FSIO_IRDA

x

 register = 0). Do not set it to 1/8 (DIVMD = 1).

 

•  Although Figure 20.8.3.2 shows the input signal as a low pulse of a 3 

×

 SIO_CLK width, the 

RZI circuit recognizes low pulses by means of the signal edge (rising edge when IRRL = 0; 
falling edge when IRRL = 1). Note that noise may cause a malfunction.

FSIO Interrupts and DMA

20.9  

This section describes the FSIO interrupts and DMA.
For more information on interrupt processing and DMA transfer, see the “Interrupt Controller (ITC)” chapter and 
the “DMA Controller (DMAC)” chapter, respectively.

Interrupts

20.9.1  

FSIO includes a function for generating the following three different types of interrupts.
• Transmit buffer empty interrupt
• Receive buffer full interrupt
• Receive error interrupt

Each FSIO channel outputs one interrupt signal shared by the three above interrupt causes to the interrupt controller 
(ITC). Inspect the interrupt flags and error flags to determine the interrupt cause occurred.

Transmit buffer empty interrupt

 

To use this interrupt, set TDBE_IE/FSIO_INTE

x

 register to 1. If TDBE_IE is set to 0 (default), interrupt re-

quests for this cause will not be sent to the ITC.

 

When transmit data written to the transmit data buffer is transferred to the shift register, the FSIO module sets 
TDBE_IF/FSIO_INTF

x

 register to 1, indicating that the transmit data buffer is empty. If transmit buffer empty 

interrupts are enabled (TDBE_IE = 1), an interrupt request is sent simultaneously to the ITC. An interrupt oc-
curs if other interrupt conditions are met. You can inspect the TDBE_IF flag in the interrupt handler routine to 
determine whether the FSIO interrupt is attributable to a transmit buffer empty. If TDBE_IF is 1, the next trans-
mit data can be written to the transmit data buffer by the interrupt handler routine.

 

TDBE_IF is cleared by writing 0. 

Note:  When TDBE_IF is cleared and no data is written to the transmit data buffer, subsequent interrupt 

requests will not be issued even if the transmit data buffer is empty.

Receive buffer full interrupt

 

To use this interrupt, set RDBF_IE/FSIO_INTE

x

 register to 1. If RDBF_IE is set to 0 (default), interrupt re-

quests for this cause will not be sent to the ITC.

 

When the number of data specified with FIFOINT[1:0]/FSIO_IRDA

x

 register (one data in standard mode) has 

been received in the receive data buffer, the FSIO module sets RDBF_IF/FSIO_INTF

x

 register to 1. If receive 

buffer full interrupts are enabled (RDBF_IE = 1), an interrupt request is sent simultaneously to the ITC. An 
interrupt occurs if other interrupt conditions are met. You can inspect the RDBF_IF flag in the interrupt handler 
routine to determine whether the FSIO interrupt is attributable to a receive buffer full. If RDBF_IF is 1, the 
received  data  can  be  read  from  the  receive  data  buffer  by  the  interrupt  handler  routine.  However,  be  sure  to 
check whether a receive error has occurred or not. 

 

RDBE_IF is cleared by writing 0. 

Note:  Before RDBF_IF can be cleared by writing 0, be sure to read out the received data from the re-

ceive data buffer.

Receive error interrupt

 

To use this interrupt, set RERR_IE/FSIO_INTE

x

 register to 1. If RERR_IE is set to 0 (default), interrupt re-

quests for this cause will not be sent to the ITC.

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Unipulse F160 Operation Manual preview
F160
Brand: Unipulse Pages: 99
Mainpine EPC Operating Instructions Manual preview
EPC
Brand: Mainpine Pages: 16
Danfoss AFP Series Installation Manual preview
AFP Series
Brand: Danfoss Pages: 20
Jetline 9600 Series Operation Manual preview
9600 Series
Brand: Jetline Pages: 58
Rachio IRO Installation Manual preview
IRO
Brand: Rachio Pages: 2
YASKAWA U1000 iQpump Drive Quick Start Quide preview
U1000 iQpump Drive
Brand: YASKAWA Pages: 26
YASKAWA Z1000 CIMR-ZU*A Series Quick Start Up Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 2
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Brand: IBC Pages: 8
Danfoss VLTAutomationDrive FC 360 Quick Manual preview
VLTAutomationDrive FC 360
Brand: Danfoss Pages: 52
Varian Turbo-V 250 series Instruction Manual preview
Turbo-V 250 series
Brand: Varian Pages: 79
Espressif Systems ESP32-DevKitC Getting Started Manual preview
ESP32-DevKitC
Brand: Espressif Systems Pages: 11
TDSi DIGIgarde PLUS User Manual preview
DIGIgarde PLUS
Brand: TDSi Pages: 71
Azbil AUR455 User Manual preview
AUR455
Brand: Azbil Pages: 68
Ltech LT-3900IR Manual preview
LT-3900IR
Brand: Ltech Pages: 2
Zennio MAXinBOX 24 ZIO-MB24 User Manual preview
MAXinBOX 24 ZIO-MB24
Brand: Zennio Pages: 24
KELD KLT11IB Specification And Operating Instructions preview
KLT11IB
Brand: KELD Pages: 2
Samson 46-5 Mounting And Operating Instructions preview
46-5
Brand: Samson Pages: 24
YOKOGAWA UT32A-C Operation Manual preview
UT32A-C
Brand: YOKOGAWA Pages: 10

Brands by name

Popular brands

Load more brands