manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

CONTENTS

xiv

 

Seiko Epson Corporation 

S1C33L26 TECHNICAL MANUAL

DMA_IntEnb (DMA Interrupt Enable) ...................................................................................... 28-33
FIFO_IntEnb (FIFO Interrupt Enable) ...................................................................................... 28-33
EP0IntEnb (EP0 Interrupt Enable)........................................................................................... 28-33
EPaIntEnb (EPa Interrupt Enable) ........................................................................................... 28-34
EPbIntEnb (EPb Interrupt Enable)........................................................................................... 28-34
EPcIntEnb (EPc Interrupt Enable) ........................................................................................... 28-34
EPdIntEnb (EPd Interrupt Enable)........................................................................................... 28-34
RevisionNum (Revision Number) ............................................................................................ 28-34
USB_Control (USB Control) .................................................................................................... 28-35
USB_Status (USB Status) ....................................................................................................... 28-35
XcvrControl (Xcvr Control)....................................................................................................... 28-36
USB_Test (USB Test) .............................................................................................................. 28-36
EPnControl (Endpoint Control) ................................................................................................ 28-37
EPrFIFO_Clr (EPr FIFO Clear)................................................................................................ 28-38
FrameNumber_H (Frame Number HIGH) ................................................................................ 28-39
FrameNumber_L (Frame Number LOW) ................................................................................. 28-39
EP0Setup_0 (EP0 Setup 0)–EP0Setup_7 (EP0 Setup 7) ....................................................... 28-39
USB_Address (USB Address) ................................................................................................. 28-40
EP0Control (EP0 Control) ....................................................................................................... 28-40
EP0ControlIN (EP0 Control IN) ............................................................................................... 28-41
EP0ControlOUT (EP0 Control OUT) ....................................................................................... 28-42
EP0MaxSize (EP0 Max Packet Size) ...................................................................................... 28-42
EPaControl (EPa Control) ........................................................................................................ 28-43
EPbControl (EPb Control) ....................................................................................................... 28-44
EPcControl (EPc Control) ........................................................................................................ 28-44
EPdControl (EPd Control) ....................................................................................................... 28-45
EPaMaxSize_H (EPa Max Packet Size HIGH) ........................................................................ 28-46
EPaMaxSize_L (EPa Max Packet Size LOW).......................................................................... 28-46
EPaConfig_0 (EPa Configuration 0) ........................................................................................ 28-47
EPaConfig_1 (EPa Configuration 1) ........................................................................................ 28-47
EPbMaxSize_H (EPb Max Packet Size HIGH) ........................................................................ 28-47
EPbMaxSize_L (EPb Max Packet Size LOW) ......................................................................... 28-47
EPbConfig_0 (EPb Configuration 0) ........................................................................................ 28-48
EPbConfig_1 (EPb Configuration 1) ........................................................................................ 28-48
EPcMaxSize_H (EPc Max Packet Size HIGH) ........................................................................ 28-49
EPcMaxSize_L (EPc Max Packet Size LOW) .......................................................................... 28-49
EPcConfig_0 (EPc Configuration 0) ........................................................................................ 28-49
EPcConfig_1 (EPc Configuration 1) ........................................................................................ 28-49
EPdMaxSize_H (EPd Max Packet Size HIGH) ........................................................................ 28-50
EPdMaxSize_L (EPd Max Packet Size LOW) ......................................................................... 28-50
EPdConfig_0 (EPd Configuration 0) ........................................................................................ 28-50
EPdConfig_1 (EPd Configuration 1) ........................................................................................ 28-50
EPaStartAdrs_H (EPa FIFO Start Address HIGH) .................................................................. 28-51
EPaStartAdrs_L (EPa FIFO Start Address LOW) ................................................................... 28-51
EPbStartAdrs_H (EPb FIFO Start Address HIGH) .................................................................. 28-51
EPbStartAdrs_L (EPb FIFO Start Address LOW) ................................................................... 28-51
EPcStartAdrs_H (EPc FIFO Start Address HIGH) .................................................................. 28-52
EPcStartAdrs_L (EPc FIFO Start Address LOW) .................................................................... 28-52
EPdStartAdrs_H (EPd FIFO Start Address HIGH) .................................................................. 28-52
EPdStartAdrs_L (EPd FIFO Start Address LOW) ................................................................... 28-52
CPU_JoinRd (CPU Join FIFO Read) ...................................................................................... 28-53
CPU_JoinWr (CPU Join FIFO Write) ....................................................................................... 28-53
EnEPnFIFO_Access (EPn FIFO Access Enable) ................................................................... 28-54
EPnFIFOforCPU (EPn FIFO for CPU) ..................................................................................... 28-54
EPnRdRemain_H (EPn FIFO Read Remain HIGH) ................................................................ 28-55
EPnRdRemain_L (EPn FIFO Read Remain LOW) ................................................................. 28-55
EPnWrRemain_H (EPn FIFO Write Remain HIGH) ................................................................ 28-55
EPnWrRemain_L (EPn FIFO Write Remain LOW) .................................................................. 28-55
DescAdrs_H (Descriptor Address HIGH) ................................................................................ 28-55

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Microchip Technology PLECS Quick Start Manual preview
PLECS
Brand: Microchip Technology Pages: 37
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Brand: Samson Pages: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Brand: Samson Pages: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Brand: Samson Pages: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Brand: Samson Pages: 68
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Brand: Samson Pages: 80
Haehne DCX Quick Start Manual preview
DCX
Brand: Haehne Pages: 44
Fuji Electric FD5000 series Instruction Manual preview
FD5000 series
Brand: Fuji Electric Pages: 12
Nuvoton NuMicro M252 Series User Manual preview
NuMicro M252 Series
Brand: Nuvoton Pages: 38
Monde Synthesizer Ribbonz User Manual preview
Ribbonz
Brand: Monde Synthesizer Pages: 4
Samson TROVIS 5724-3 Mounting And Operating Instructions preview
TROVIS 5724-3
Brand: Samson Pages: 72
DZ Custom Innovations ShiftSense Pro V2 Installation And Operation Manual preview
ShiftSense Pro V2
Brand: DZ Custom Innovations Pages: 8
POLA HD38 Handbook preview
HD38
Brand: POLA Pages: 7
Yaesu G-5500DC Instruction Manual preview
G-5500DC
Brand: Yaesu Pages: 12
Trio MC206X Quick Connection Manual preview
MC206X
Brand: Trio Pages: 8
YASKAWA JEPMC-BU3301-E Instruction Manual preview
JEPMC-BU3301-E
Brand: YASKAWA Pages: 27
iGrid T&D iGW Series User Manual preview
iGW Series
Brand: iGrid T&D Pages: 47
Danfoss AK-PC 420 Instructions Manual preview
AK-PC 420
Brand: Danfoss Pages: 18

Brands by name

Popular brands

Load more brands