manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 96 / 168

Share
Download
Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 96

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

96

4.2.6.4  APG Assy

1. Remove the Upper Housing.

For Stylus Photo 1400/1410:

See section 4.2.1.4 on page 80.

For Stylus Photo 1390: 

See section 4.3.1 on page 128.

2. Disconnect the APF Motor Cable from connector CN9 (red) on the Main Board
3. Remove the acetate tape, and remove the Cable from the ASF Assy.
4. Disconnect the Connector Cables from the two APG Sensor Connectors.

Figure 4-54.  Disconnecting the Connector Cables

5. Remove the three C.B.S. 3x6 screws that secure the APG Assy and remove the 

APG Assy from the Main Frame. 

Figure 4-55.  Removing the APG Assy

Tighten the screws in the order shown in 

Figure 4-52.

A D J U S T M E N T

R E Q U I R E D

After replacing or removing the Printhead, the following 
adjustment must be performed.

1. PG Adjustment 

(p.132)

2. Head ID Input (only after replacing) 

(p.132)

3. Head Angular Adjustment 

(p.132)

4. Bi-D Adjustment 

(p.132)

5. First dot position 

(p.133)

6. PW Sensor Adjustment 

(p.133)

Refer to Chapter 5 “Adjustment” for details on the adjustments.

CN9

APG Motor

APG Assy

APG Sensor Connectors

Acetate Tape

3

1

2

2) C.B.S. 3x6

(8±1 kgf.cm)

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Reviews:

No comments