Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 104

Page: 104 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

104

20. Turn the Belt Holder Mounting Plate in the direction of the arrow, and remove it

from the Carriage Unit.

Figure 4-80. Removing the Belt Holder (1)

21. Remove the Belt Holder from the Carriage unit.

Figure 4-81. Removing the Belt Holder (2)

22. Release the CR Encoder Board Holder from the three tabs to remove it from the

Carriage Unit.

Figure 4-82. Removing the CR Encoder Board Holder

23. Disconnect the Sensor FFC from the CR Encoder Board, pull out the Sensor FFC

from the Carriage Unit, and remove the Carriage Unit.

Figure 4-83. Removing the Carriage Unit

Belt Holder Mounting Plate

Belt Holder

CR Encoder Board Holder

Tabs

CR Encoder Board

Sensor FFC

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 104 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: