manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 112 / 168

Share
Download
Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 112

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

112

8. Remove the Ink System Unit downwards from the Main Frame. For Stylus 1400/

1410, remove it while keeping the Unit from coming in contact with the Paper EJ 
Transmission Lock Lever.

Figure 4-103.  Removing the Ink System Unit

When the Ink System Unit is removed from the Printer 
Mechanism, the Paper EJ Lock Release Cam may drop off. In such 
case, correctly install it referring to the figure below. (The Stylus 
Photo 1390 is not equipped with the Paper EJ Lock Release Cam.)

Figure 4-104.  Installing the Paper EJ Lock Release Cam

Paper EJ 

Transmission 

Lock Lever

Ink System Unit

Paper EJ Lock Release Cam

Stylus Photo 1400/1410 only

„

Place the Paper EJ Lock Release Cam on the rear side of the 
Paper EJ Transmission Lock Lever. (The Stylus Photo 1390 is 
not equipped with the Paper EJ Transmission Lock Lever.)

Figure 4-105.  Installing the Ink System Unit (1)

„

Align the positioning hole on the Main Frame with the guide 
pin on the Ink System Unit.

Figure 4-106.  Installing the Ink System Unit (2)

Paper EJ Lock Release Cam

Paper EJ Transmission Lock Lever

Stylus Photo 1400/1410 only

Positioning Hole

Guide Pin

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Reviews:

No comments