Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 101

Page: 101 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

101

11. Loosen the C.B.S. (P4) 3x8 screw that secures the Left Parallelism Adjust

Bushing, and rotate the Bushing toward the front of the Printer Mechanism to
prevent interference between the Flag of the Parallelism Adjust Bushing and the
Left PG Cam.

Figure 4-68. Rotating the Left Parallelism Adjust Bushing

12. Slide the Left CR Shaft Mounting Plate upwards, and release the tab on the Left

CR Shaft mounting Plate from the cutout of the Main Frame to rotate the
Mounting Plate toward you.

Figure 4-69. Rotating the Left CR Shaft Mounting Plate

13. Lift the Carriage Shaft upwards, and remove the Carriage Shaft Spacer from the

Carriage Shaft with tweezers.

Figure 4-70. Removing the Carriage Shaft Spacer

14. Rotate the Left CR Shaft Mounting Plate toward you to remove the Bushing on the

Left CR Shaft Mounting Plate from the Carriage Shaft.

Figure 4-71. Removing the Left CR Shaft Mounting Plate

6) C.B.S. (P4) 3x8

(5±1 kgf.cm)

Left PG Cam

Flag of the Parallelism Adjust Bushing (Left)

Left CR Shaft

Mounting Plate

Tab

Carriage

Shaft

Carriage Shaft Spacer

Left CR Shaft

Mounting Plate

Bushing

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 101 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: