Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 73

Page: 73 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Overview

4.1.2 Tools

The following table indicates the tools recommended for disassembly/assembly.
All are commercially available, and should be ready beforehand.

4.1.3 Screws

The following table lists the screws used in this product. When disassembling and
reassembling the printer, refer to the following table and use the specified screws in the
specified positions.

Table 4-1. List of Tools

Tool Name

Tool Code

Phillips Screw Driver, No.1

1080530

Phillips Screw Driver, No.2

1080532

Flat-blade Screwdriver

1080527

Tweezers

1080561

Needle nose pliers

1080564

Acetate Tape

1003963

PF Tension Measuring Tool

1231678

Penlight

---

Table 4-2. List of Screw Types

Image

Description

Image

Description

1) C.B.P. 3x10

2) C.B.S. 3x6

3) C.B.S. (P2) 3x10

4) C.B.P. 3x8

5) C.B.S. 3x8

6) C.B.S. (P4) 3x8

7) C.B.P. 2.6x8

8) C.B.S. (P4) 3x6

9) C.B.P. 3x6

10) C.B.S. 3x4

11) C.C. 3x4

12) C.P.B. (P1) 1.7x5

13) C.B.P. 2.6x5

14) C.P.S. 3x10

15) C.B.P. 3x10

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 73 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: