manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 128 / 168

Share
Download
Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 128

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Procedure Specific to Stylus Photo 1390

128

4.3  Procedure Specific to Stylus Photo 1390

This section describes disassembly procedures of the Upper Housing and the Paper EJ 
Frame Assy of Stylus Photo 1390.

4.3.1  

Upper Housing

1. Open the Printer Cover and the Paper Support.

2. Remove the two C.B.S. 3x6 screws, and open the Front Cover. 

Figure 4-146.  Opening the Front Cover

3.

Remove the Side Housing. See Section 4.2.1.2 on page 78.

4. Remove the four C.B.P. 3x10 screws, three C.B.S. 3x6 screws, and two C.B.P. 

3x10 screws that secure the Upper Housing.

Figure 4-147.  Screws that Secure the Upper Housing

Printer Cover

2) C.B.S. 3x6

(6±1 kgf.cm)

Front Cover

Paper 

Support

1

Guide Pin

3

Guide Pin

5

4

9

Tab

2

6

Tab

7

8

1) C.B.P. 3x10

(6±1 kgf.cm)

2) C.B.S. 3x6

(6±1 kgf.cm)

15) C.B.P. 3x10

(6±1 kgf.cm)

Upper 

Housing

Front Cover

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Reviews:

No comments