Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 84

Page: 84 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

4.2.2 Waste Ink Pad

1. Remove the Lower Housing.

See section 4.2.1.5 on page 82.

2. Remove the C.B.P. 3x8 screw that secures the Waste Ink Tube.

3. Remove the 11 Waste Ink Pads from the Lower Housing.

Figure 4-21. Removing the Waste Ink Pads

4) C.B.P. 3x8

(6±1 kgf.cm)

Waste Ink Pads

Route the Waste Ink Tube as shown below.

Figure 4-22. Positions of Waste Ink Tubes

Referring to

Figure 4-23

, correctly install the Waste Ink Pads.

Figure 4-23. Installing the Waste Ink Pads

A D J U S T M E N T

R E Q U I R E D

After replacing or removing the Waste ink Pads, be sure to make
the following adjustments.

Waste Ink Protection Counter Reset

(p.134)

Refer to Chapter 5 “Adjustment” for details on the adjustment.

Waste Ink Tubes

Installation

Order

Installation

Order

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 84 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: