Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 51

Page: 51 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

At power-on

After the Carriage has detected
the HP, an error is displayed on
the LED and STM3.

CSIC FFC

1. Check that the CSIC FFC is connected to the CSIC Board

Connector and Main Board Connector CN15.

1. Connect the CSIC FFC to the CSIC Board

Connector and Main Board Connector CN15.

2. Check the CSIC FFC for damage.

2. Replace the CSIC FFC with a new one.

CSIC Board

1. Check the CSIC Board for damage.

1. Replace the CSIC Board with a new one.

Carriage Unit

1. Check that the electrodes on the CSIC Board, which make

contact with the Ink Cartridge are not bent.

1. Replace the Carriage Unit with a new one.

Table 3-9. Troubleshooting of No Ink Cartridge/CSIC Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

CN15

CSIC Board

Connector

CSIC FFC

CSIC Board

Electrode

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 51 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: