Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 145

Page: 145 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

ADJUSTMENT

Adjustment

145

4. Loosen the screws that secure the Center Support Bushing Cam and the Center

Support Bush.

Figure 5-14. Center Support Bushing Cam and the Screw

5. Set the jig in place on the PF Roller Shaft as shown in the figure below.

Left side: Inside of PF Roller left end (E-ring)

Right side: Gap between PF Roller right end (Right Bushing 8) and left end

of Upper Paper Guide

Center:

Gap between the 2nd Upper Paper Guide and 3rd one from the

left

Figure 5-15. Setting the PF Roller Shaft Position Adjustment Jig

C A U T I O N

Check if any dirt is on the PF Roller Shaft. If there is, remove it
before performing the following procedure.

Center Support

Bushing Cam

Bottom of Rear Center

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 145 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: