Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 85

Page: 85 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

4.2.3 Front Paper Guide Pad

1. Remove the Printer Mechanism.

See section 4.2.1.5 on page 82.

2. Remove the Front Paper Guide Pads and Front Paper Guide Pad Protection from

the Front Paper Guide with tweezers.

Figure 4-24. Removing the Front Paper Guide Pads and

the Front Paper Guide Pad Protection

C A U T I O N

Make sure that the grease contained in the Front Paper Guide Pads
and the Front Paper Guide Pad Protection do not stick to other
parts.

Front Paper Guide

Front Paper Guide Pads

Front Paper Guide Pad

Protection

After installing the Front Paper Guide Pads and Front Paper Guide
Pad Protection, lift the Printer Mechanism, and check the following
points.

1. Make sure that the tabs on the Pads are not cut midway.
2. Make sure that all tabs are in place on the Front Paper

Guide, and that they are facing down (toward the Waste Ink
Pads) without any folds.

3. Make sure that the turned edges of the tabs are protruding

completely from the Front Paper Guide.

Figure 4-25. Installing the Front Paper Guide Pad (1)

4. Make sure that the Pad is placed under a tab of the Front

Paper Guide.

Figure 4-26. Installing the Front Paper Guide Pad (2)

5. Make sure that all the tabs on the Pads are fitted into the

securing section under the Front Paper Guide.

Tabs

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 85 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: