Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 109

Page: 109 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

109

6. Remove Spur Gear 68 from the Paper EJ Roller Shaft.

Figure 4-93. Removing the Spur Gear 68

7. Remove the C.B.P. 3x6 screw that secures the Left CD-R Release Lever Sub Assy.

8. Push the small tab of the Left CD-R Release Lever Sub Assy with a flat-blade

screwdriver, and remove the Left CD-R Release Lever Sub Assy upwards from the
Main Frame.

Figure 4-94. Removing the Left CD-R Release Lever Sub Assy

Spur Gear 68

9) C.B.P. 3x6

(6±1 kgf.cm)

Tabs

Small Tab

Make sure that the Left CD-R Release Lever Sub Assy is
correctly assembled as shown in the figure below.

Figure 4-95. Reinstalling the Left CD-R Release Lever Sub Assy (1)

Align the Shaft and Bushing.

Figure 4-96. Removing the Left CD-R Release Lever Sub Assy (2)

Align the two tabs on the Left CD-R Release Lever Sub Assy
with the positioning holes on the Main Frame.

See Figure 4-94.

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 109 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: