Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 5

Page: 5 / 168

Revision Status

Revision

Date of Issue

Description

October 20, 2006

First Release

January 17, 2007

All Chapters:

• Check points and notes are added to provide information specific to Stylus Photo 1390.

Chapter 1:

•

1.1"Overview" (Page 9)

Features are modified.

•

1.6"Accessories" (Page 20)

Information on the ink cartridge of Stylus Photo 1390 is added.

Chapter 4:

•

4.2"Disassembly/Assembly Procedures" (Page 76)

Flowchart for Stylus Photo 1390 is added.

•

4.3"Procedure Specific to Stylus Photo 1390" (Page 128)

Disassembly procedures specific to Stylus Photo 1390 are added.

Chapter 5:

•

5.1.1"Servicing Adjustment Item List" (Page 132)

Description of Bi-D Adjustment is corrected.

Chapter 7:

•

7.3"Electrical Circuit Diagrams" (Page 162)

Electrical Circuit Diagrams of C655 Main1 is revised.

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 5 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: