manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 137 / 168

Share
Download
Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 137

EPSON Stylus Photo 1390/1400/1410

Revision B

ADJUSTMENT

Adjustment

137

5.1.3  Required Adjustment Tools

The following table lists the adjustment tools required for adjustment of this product.

5.2  Adjustment

This section explains the adjustments that do not use the Adjustment Program.

5.2.1  PF Belt Tension Adjustment

When either of the following parts has been removed or replaced, this adjustment must 
be performed to reduce load on the PF Motor and to secure paper feed accuracy.

„

PF Motor

„

PF Roller Shaft

The PF Tension Measuring Tool is used for this adjustment.

Figure 5-1.  PF Tension Measuring Tool

Table 5-5.  List of Tools

No.

Name

Part Code

Category

Overview

1

Adjustment 
Program

–

Software

This adjustment program is designed to 
display the required adjustment items in 
the appropriate order when a replacement 
part is selected, and provides workers 
with the accurate adjustment order.

2

G-26

1080614

Grease

For the Parallelism Adjust Bushing, 
Lower Paper Guide, Driven Release 
Shaft, etc.

3

G-45

1033657

Grease

For the PF Roller, Front Paper Guide, 
Rear Paper Guide and etc.

4

G-71

1304682

Grease

For the Carriage Unit and Carriage Shaft.

5

PG Adjustment 
Gauge

1276333

Gauge

A gauge exclusively used to make PG 
Adjustment. Check the correction value 
by energizing it in the same way as for 
Stylus Photo R1800.

6

PF Tension 
Measuring Tool

1231678

Measuring 

tool

Used to check whether or not the tension 
of the PF Drive Belt is within the 
specified value. If load is more than the 
specified value, the PF Motor may 
generate heat and burning off the coil. 
Reversely, if load is less than the 
specified value, the paper feed position 
may be shifted.

7

PF Roller Shaft 
Position 
Adjustment Jig

1304993

Adjusting

jig

Used to check whether or not the 
deflection amount of the PF Roller Shaft 
is within the specified value. The jig is 
used together with the Level Block.

8

Level Block

1304994

Adjusting

jig

Used to check whether or not deflection 
amount of the PF Roller Shaft is within 
the specified value. The jig is used 
together with the PF Roller Shaft Position 
Adjustment Jig.

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Reviews:

No comments