manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 48 / 168

Share
Download
Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 48

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

48

Table 3-5.  Troubleshooting of Paper Jam Error

Occurrence 

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At operation

At the time of paper ejection, the 
PF Roller advances the paper but 
cannot eject it completely.

–

1. Check that the size of the fed paper is not larger than that of the 

paper specified by the driver.

1. Tell the user that the paper size specified by the 

driver is not available for the printer.

Paper is not ejected completely 
and causes a jam near the Paper 
Eject Frame.

ASF Assy.

1. Check that the paper is fed along the Right Edge Guide.

1. Feed the paper along the Right Edge Guide.

Paper EJ Frame 
Assy.

1. Check that the Star Wheel Units have not come off the Paper EJ 

Frame Assy.

1. Securely install the Star Wheel Units to the 

Paper EJ Frame Assy.

2. Check the Paper EJ Frame Assy for deformation or damages.

2. Replace the Paper EJ Frame Assy with a new 

one.

Spur Gear 68 
Spur Gear 16; B
Paper EJ Roller 
Assy (front/rear)

1. Check the Spur Gear 68 or Spur Gear 16; B for damages.

1. Replace the Front (or Rear) Paper EJ Roller 

Assy with a new one.

Paper EJ Frame Assy

Star Wheel Units

Spur Gear 16; B

Spur Gear 68

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Reviews:

No comments