Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 158

Page: 158 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

APPENDIX

Connector Summary

158

7.1 Connector Summary

This section shows connections between main components of Stylus Photo 1390/1400/
1410.

Figure 7-1. Connections of Main Components

7.1.1 Connectors and Pin Layouts

See the following tables for the connector summary of the C655 MAIN Board and each
connector's pin alignment.

Note *:

Stylus Photo 1390 does not have the connector.

Not equipped for Stylus Photo 1390

Table 7-1. Connector Summary

Connector

Function

Reference

CN1

USB Device

Table 7-2

CN2

USB Host*

Table 7-3

CN3

Relay Board

Table 7-4

CN4

Power Supply

Table 7-5

CN5

Panel

Table 7-6

CN6

CR Motor

Table 7-7

CN7

PF Motor

Table 7-8

CN8

Pump Motor

Table 7-9

CN9

APG Motor

Table 7-10

CN10

Printhead

Table 7-11

CN11

Printhead

Table 7-12

CN12

Printhead

Table 7-13

CN13

ASF Motor

Table 7-14

CN14

Sensors

Table 7-15

CN15

CSIC

Table 7-15

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 158 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: