Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 42

Page: 42 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

At power-on

The printer does not operate at
all.

Power Supply
Board

1. Check that the Connector Cable of the Power Supply Board is

connected to the Main Board Connector CN4.

1. Connect the Connector Cable of the Power

Supply Board to the Main Board Connector
CN4.

2. Make sure that the Power Supply Board connector cable is

inserted into the Main Board Connector CN4 with the blue line
on the cable facing the Pin 1 side of the connector as shown in
the picture above.

2. Reconnect the Power Supply Board Connector

cable so that the blue line is inserted into the
Pin 1.

3. Check that the Fuse F1 on the Power Supply Board has not

blown.

3. Replace the Power Supply Board with a new

one.

4. Check the components on the Power Supply Board for damage.

4. Replace the Power Supply Board with a new

one.

Table 3-2. Troubleshooting of Communication Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

Power Supply Board

connector cable

Blue line

Pin 1 side

CN4

Fuse F1

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 42 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: