manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 134 / 168

Share
Download
Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 134

EPSON Stylus Photo 1390/1400/1410

Revision B

ADJUSTMENT

Adjustment Items and Overview

134

Table 5-2.  Maintenance Functions

Function Item

Purpose

Method Outline

Ink Charge

This function is used for Printhead replacement to drain Shipping 
Liquid of the after-sales service part in the head flow path and 
simultaneously fill ink in the head flow path to make all nozzles 
printable and stabilize the ink in the Printhead.

1. Select this function in the Adjustment Program.
2. Transfer the factory-set command (CL execution command (Initial Ink Charge) is used as the 

command) to the printer to make the printer perform Initial Ink Charge operation.

Refurbishment Function 
(Shipping Liquid 
replacement)

This function is used to refurbish the initially returned product. 
Specifically, clean the inside of the Head, and charge and replace 
the Shipping Liquid.

1. Select this function in the Adjustment Program.

Cleaning

This function is used to execute cleaning 3 (CL3) when ink is not 
delivered from the Printhead properly, e.g. dot missing or skewed 
injection.

1. Select this function in the Adjustment Program.
2. Execute CL3.

Waste Ink Counter Reset

This function is used to read and reset the Waste Ink Counters.

1. In the Adjustment Program, select data read or reset from this function.

Before executing this function, replace the Waste Ink Pads on both the 0 digit and 130 digit side.

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Reviews:

No comments