Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 60

Page: 60 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

At power-on

At power-on, the PF Roller
rotates fast about a half turn.

PF Scale

1. Check that the PF Scale is inserted in the slit of the PF Encoder

Sensor.

1. Install the PF Scale in the slit of the PF

Encoder Sensor correctly.

2. Check the PF Scale for damages and dirt.

2. Replace the PF Scale with a new one.

During printing*

After receiving a print data, or
while performing the CD/DVD
Tray home position detection
sequence, an error is displayed
on the LED and STM3.

CSIC FFC
Head FFC
Sensor FFC

1. Check that the CSIC FFC, Head FFC, and the Sensor FFC are

securely connected to the Main Board Connectors CN10, CN11,
CN12, CN14 and CN15.

1. Connect the CSIC FFC, Head FFC, and the

Sensor FFC to the Main Board Connectors
CN10, CN11, CN12, CN14 and CN15.

Table 3-11. Troubleshooting of Fatal Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

Slit

PF Scale

CN10, CN11, CN12, CN14 and CN15

Note *:

Stylus Photo 1390 does not have the CD/DVD-related units.

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 60 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: