Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 100

Page: 100 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

100

7. Remove the Extension Spring for the Driven Pulley Holder from the Main Frame

and the tab on the Drive Pulley Holder with needle-nose pliers.

Figure 4-64. Removing the Extension Spring for the Driven Pulley Holder

8. Slide the Driven Pulley Holder to the right end of the cutout on the Main Frame,

then remove it toward you.

Figure 4-65. Removing the Driven Pulley Holder

9. Remove the CR Drive Belt from the CR Motor Pinion Gear.

Figure 4-66. Removing the CR Drive Belt

10. Remove the four C.B.S. (P4) 3x6 screws that secure the CR Guide plate, and

remove it from the Main Frame.

Figure 4-67. Removing the CR Guide Plate

Tabs

Extension Spring for the

Driven Pulley Holder

Align the positioning holes of the CR Guide Plate with the seven
tabs on the Main Frame.

See Figure 4-67.

Tighten the screws in the order shown in

Figure 4-67.

CR Drive Belt

CR Motor Pinion Gear

8) C.B.S. (P4) 3x6

(8±1 kgf.cm)

8) C.B.S. (P4) 3x6

(8±1 kgf.cm)

CR Guide Plate

Tabs

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 100 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: