manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 45 / 168

Share
Download
Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 45

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

45

At operation

Though paper is fed from the 
ASF Assy, it stops near the PE 
Sensor Lever.

PE Sensor

1. Check that the Connector cable of the PE Sensor is securely 

connected to the PE Sensor and Relay Board Connector CN2.

1. Connect the Connector cable of the PE Sensor 

to the PE Sensor and Relay Board Connector 
CN2.

2. Check that the Sensor Holder is mounted to the Mechanical 

frame correctly.

2. Install the Sensor Holder correctly.

3. Move the Detection Lever manually as when the paper passes, 

and check that the Detection Lever returns to the original 
position automatically by the Torsion Spring when released. 
Refer to the above photo.

3. Replace the PE Sensor Holder Unit with a new 

one.

4. Using a tester, check that the PE Sensor is normal.

⋅

 Paper absent: 2.4V or more

⋅

 Paper present: 0.4V or less

4. Replace the PE Sensor Holder Unit with a new 

one.

Table 3-4.  Troubleshooting of Paper Out Error

Occurrence 

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

CN2

PW Sensor Connector

Sensor Holder

Detection Lever

Torsion Spring

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Reviews:

No comments