manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 79 / 168

Share
Download
Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 79

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

79

4.2.1.3  Locking/Releasing the Carriage and Opening/Closing

the CD-R Unit

Locking/releasing the Carriage and opening/closing the CD-R Unit are mutually 
related. The CD-R Unit cannot be opened when the Carriage Lock is released.

1. Remove the Right Side Housing. 

See section 4.2.1.2 on page 78.

2. Insert the flat-blade screwdriver into the hole on the right side of the frame, and 

rotate the white shaft of the Ink System Unit.

Figure 4-10.  Locking/Releasing the Carriage and Opening/Closing the CD-R Unit

C H E C K

P O I N T

If you are servicing Stylus Photo 1390, refer to this section only for 
locking and releasing the Carriage. Stylus Photo 1390 does not have 
the CD-R Unit.

Table 4-3.  Relation between Carriage Lock and CD-R Unit

Direction of Rotation

Carriage

CD-R Unit

Clockwise (CW)

Locked

Can be opened/closed.

Counterclockwise (CCW)

Released

Locked

CCW

CW

White Shaft

C A U T I O N

When moving the Carriage Unit with the CD-R Unit opened, turn 
the PG CAM (Right) beforehand so that PG ++ points downwards 
to release the PG in order to prevent interference between the 
Paper EJ Frame and Carriage Unit.

Figure 4-11.   Interference between the Frame and Carriage Unit

PG Cam (Right)

Interference 

point

Paper EJ Frame

PG ++ position

Carriage 

Unit

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Reviews:

No comments