manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 55 / 168

Share
Download
Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 55

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

55

At power-on

At power-on, the APG Motor 
does not operate at all.

APG Motor

1. Check that the Connector Cable of the APG Motor is connected 

to the Main Board Connector CN9.

1. Connect the APG Motor connector cable to the 

Main Board Connector CN9.

2. Check the APG Motor connector cable for damage.

2. Replace the APG Motor with a new one.

3. Check if the APG Motor operates normally.

3. Replace the APG Motor with a new one.

At power-on, the Pump Motor 
does not operate at all.

Pump Motor

1. Check that the Pump Motor connector cable is connected to the 

Relay Connector.

1. Connect the Pump Motor connector cable to 

the Relay Connector.

2. Using a tester, check the resistance value of the Pump Motor.

Value of resistance: 10.3

Ω

 ±

 

10%

2. If the resistance value is abnormal, replace the 

Ink System Unit with a new one.

3. Check the Pump Motor connector cable for damages.

3. Replace the Ink System Unit with a new one.

Table 3-11.  Troubleshooting of Fatal Error

Occurrence 

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

CN9

APG Motor

Relay Connector

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Reviews:

No comments