Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 110

Page: 110 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

110

4.2.6.9 Ink System Unit

1. For Stylus Photo 1400/1410:

Remove the Right CD-R Release Lever Sub Assy.

See section 4.2.6.8 on page 107.

For Stylus Photo 1390:
Remove the Printer Mechanism.

See section 4.2.1.5 on page 82.

Remove the Paper EJ Frame Assy.

See section 4.2.6.7 on page 106.

2. Release the Carriage lock, and move the Carriage Unit to the center.

See section 4.2.1.3 on page 79.

3. Remove the C.B.S. 3x8 screw that secures the Earth Cable to remove the Earth

Cables, and untie the Earth Cable from the Relay Connector Cable.

4. Disconnect the Pump Motor Connector from the Relay Connector.

Figure 4-97. Disconnecting the Pump Motor Connector

5. Remove the two C.B.S. 3x4 screws that secure the Ink System Guide Plate, and

remove it.

Figure 4-98. Removing the Ink System Guide Plate

Be sure to screw the two Earth Cables together.

Referring to

Figure 4-97

, correctly route the Relay Connector

Cable.

5) C.B.S. 3x8

(8±1 kgf.cm)

Relay Connector

Earth Cable

Relay Connector Cable

Align the cutout on the Ink System Guide Plate with the cutout
on the Main Frame.

Figure 4-99. Installing the Ink System Guide Plate

Tighten the screws in the order shown in

Figure 4-98.

10) C.B.S. 3x4

(8±1 kgf.cm)

Ink System Guide

Plate

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 110 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: