Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 20

Page: 20 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

PRODUCT DESCRIPTION

Size and Weight

1.5 Size and Weight

Dimensions

Storage:

615 mm (24.2 in.) W x 314 mm (12.4 in.) D x 223 mm (8.8 in.) H

Printing:

615 mm (24.2 in.) W x 803 mm (31.6 in.) D x 413 mm (16.3 in.) H

Weight

11.5 Kg (25.4 lbs.)

Figure 1-12. Physical Dimensions

1.6 Accessories

Standard accessories

User’s guide

Ink cartridge (one for each of the six colors)

Software CD-ROM

Setup sheet

On-line questionnaire sheet

Customer Satisfaction Card (information card)

Guarantee card

CD/DVD print kit (

Stylus Photo 1390 does not support CD-R/DVD-R print.

)

CD/DVD tray

Small CD insert

Consumable and optional supplies

Ink cartridge

Network Print Server

Color

Stylus Photo 1390

Stylus Photo 1400

Stylus Photo 1410

Black

T0851

T0791

T0811

Cyan

T0852

T0792

T0812

Magenta

T0853

T0793

T0813

Yellow

T0854

T0794

T0814

Light Cyan

T0855

T0795

T0815

Light Magenta

T0856

T0796

T0816

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 20 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: