Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 129

Page: 129 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Procedure Specific to Stylus Photo 1390

129

5. Disconnect the Panel FFC from connectors CN1 on the Switch Board.

Figure 4-148. Disconnecting the Panel FFC

6. Remove the Guide Pins from the two tabs shown in

Figure 4-147

, and remove the

Upper Housing upwards.

4.3.2

Paper EJ Frame Assy

1. Remove the Upper Housing.

See section 4.3.1 on page 128.

2. Remove the Left Frame Support Plate.

See Step 2 in Section 4.2.6.5 on page 98.

3. Put back the rotation position of the Right PG Cam.

4. Remove the four C.B.S. 3x6 screws that secure the Paper EJ Frame Assy.

Figure 4-149. Screws that Secure the Paper EJ Frame Assy

Align the Guide Pins with the positioning holes of the Upper
Housing.

See Figure 4-147.

Tighten the screws in the order shown in

Figure 4-147.

CN1

Panel FFC

Guide Pin

Tabs

2) C.B.S. 3x6

(8±1 kgf.cm)

Tabs

Paper EJ Frame Assy

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 129 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: