Epson 1400 - Stylus Photo Color Inkjet Printer Service Manual Download Page 41

Page: 41 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

Table 3-2. Troubleshooting of Communication Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At power-on

The printer does not operate at
all.

Panel FFC

1. Check that the Panel FFC is connected to the Panel Board

Connector and Main Board Connector CN5.

1. Connect the Panel FFC to the Panel Board and

Main Board connector CN5.

2. Check the Panel FFC for damages.

2. Replace the Panel FFC with a new one.

Panel Board

1. Check the Panel Board for damages.

1. Replace the Panel Board with a new one.

Panel FFC

CN5

Panel FFC

Panel Board

connector

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer









































































































































































Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews:

Epson 1400 - Stylus Photo Color Inkjet Printer, Service Manual, Page: 41 / 168

Search results

Summary of Contents for 1400 - Stylus Photo Color Inkjet Printer

Reviews: