Section 3: Operation
3-56
User’s Manual
When using a 3D Stereo Sync cable at the Mirage GPIO port, select which 3D Stereo
Sync input (A or B) is connected, adjust the 3D delay, and choose the 3D Stereo Sync
locking/inversion options applicable for your installation. See below.
The following sources are optimized for active 3D (stereographic) images using the
projector and active glasses. Clamp Location is “Back Porch”. Keep in mind that
formats beyond those shown below may also be compatible.
Table 3.4. Compatible 3D Sources
Horizontal Timing Parameters (Pixels)
Vertical Timing Parameters (Lines)
Glasses Speed
Vert. Rate
Pixel Rate
Front Porch
Sync Width
Back Porch
Front Porch
Sync Width
Back Porch
closed <600 µs 96 Hz
✽
146.127
MHz
144
80
188
2
4
30
closed <600 µs 96 Hz
✽ ✽
152.928
MHz
50
60
110
2
4
32
closed <600 µs 100 Hz
✽ ✽
159.300
MHz
50
60
110
2
4
32
closed <600 µs
105 Hz
✽ ✽
159.382
MHz
20
40
92
2
4
30
closed in 200 µs 108 Hz
✽ ✽
159.329
MHz
20
40
84
2
4
6
n/a 115
Hz
✽ ✽ ✽
216
MHz
10
180
180
1
2
11
✽
1024 x 1024
✽ ✽
1280 x 1024
✽ ✽ ✽
1400 x 1050
Refer to the following guide if 3D (stereographic) images displayed by your projector
do not appear as you expect:
FLICKERING IMAGE
: Increase the incoming frame rate as much as possible.
IMAGE IS COMPRESSED HORIZONTALLY
: Increase pixel tracking. If already
maximized, the pixel clock rate of the source is too high for the projector.
3D CROSS-TALK (GHOSTING)
: 1) Make sure the IR emitter is not blocked and that its
signals can reach glasses. 2) If using a Pi Cell polarizer and passive glasses, make sure you
are using a screen that maintains polarity. 3) Are depleted batteries slowing down the
active glasses? 4) Fix timing parameters in your source. 5) Adjust Dark Interval setting.
NO IMAGE, JUMPY IMAGE, OR NOISE AT IMAGE TOP
: Your video card’s minimum
timings for blanking and pulse width are too slow for use with the projector.
WITHOUT GLASSES, I SEE ONLY A SINGLE IMAGE
: You are not in 3D mode.
WITH GLASSES, PERSPECTIVE APPEARS “REVERSED”
: If vanishing points of objects
appear in the foreground rather than background, destroying perspective, the TTL
inverter is likely missing or not working (you can confirm this by turning the glasses
upside-down—3D perspective will return). Or, if you are using the 3D Stereo Sync
Cable, the 3D Stereo Sync setting in the Advanced Image Settings menu needs to be
needs to be toggled (inverted from its current setting).
Compatible 3D Sources
'
3D
Troubleshooting
'
Signal OUT
to engine
Summary of Contents for DS+4K
