Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 626 / 1000

Fig. 105: Main Cap Bolt Hole Tightening Sequence

Courtesy of GENERAL MOTORS CORP.

7. Install the bearing, bearing cap, bolts and studs.

Tighten:

1. Tighten the M10 bolts (1-10) a first pass in sequence to 20 N.m (15 lb ft).

2. Tighten the M10 bolts (1-10) a final pass in sequence to 80 degrees using the

J 45059

3. Tighten the M10 studs (11-20) a first pass in sequence to 20 N.m (15 lb ft).

4. Tighten the M10 studs (11-20) a final pass in sequence to 53 degrees using the

J 45059

5. Tighten the M8 bolts to 25 N.m (18 lb ft).

Tighten the bolt on one side of the bearing cap and then tighten the bolt on the opposite side of the
same bearing cap.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:03:14 AM

Page 110

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands