Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 602 / 1000

Fig. 83: Engine Block Rear Oil Gallery Plug
Courtesy of GENERAL MOTORS CORP.

8. Remove the engine block rear oil gallery plug.

9. Inspect the O-ring seal of the rear oil gallery plug.

If the O-ring seal is not cut or damaged, the plug and O-ring seal may be used during assembly.

Fig. 84: Engine Block Front Oil Gallery Plug

Courtesy of GENERAL MOTORS CORP.

IMPORTANT:

Remove the front oil gallery plug only if service is required.

If the front oil gallery plug is removed, a NEW oil gallery plug must

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:03:13 AM

Page 86

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands