Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 831

Page: 831 / 1000

Fig. 16: Drilling Cylinder Head Bolt Hole

Courtesy of GENERAL MOTORS CORP.

8. Drill out the threads of the damaged hole.

Drill the hole until the stop collar of the drill bit or the sleeve contacts the bushing.

9. Using compressed air, clean out any chips.

IMPORTANT: During the reaming process, it is necessary to repeatedly remove the drill

and clean the chips from the hole.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 3 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:06:35 AM

Page 18

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands