Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 404 / 1000

Fig. 282: J 41476 & Bolts

Courtesy of GENERAL MOTORS CORP.

6. Rotate the crankshaft as required until two opposing flywheel bolt holes are parallel to the oil pan surface,

if required.

7. Install the

J 41476

bolts until snug. Do not overtighten, if required.

Tighten:

NOTE:

Refer to Fastener Notice in Cautions and Notices.

IMPORTANT: The tapered legs of the alignment tool must enter the rear cover oil seal

bore.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:46 AM

Page 304

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands