Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 104

Page: 104 / 1000

3. Rotate the A/C drive belt tensioner clockwise in order to relieve tension on the drive belt.

4. Remove the A/C drive belt from the pulleys.

5. Slowly release tension on the A/C drive belt tensioner.

6. Remove the breaker bar and socket from the A/C drive belt tensioner bolt.

7. Clean and inspect the drive belt surfaces of the pulleys.

Installation Procedure

Fig. 4: Accessory Drive Belt & Breaker Bar

Courtesy of GENERAL MOTORS CORP.

1. Install the A/C drive belt around the crankshaft balancer.

2. Install a breaker bar with hex-head socket to the A/C drive belt tensioner bolt.

3. Rotate the A/C drive belt tensioner clockwise in order to relieve tension on drive belt tensioner.

4. Install the A/C drive belt under the idler pulley.

5. Install the A/C drive belt over the A/C compressor pulley.

6. Slowly release tension on the A/C belt tensioner.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:32 AM

Page 4

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands