Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 914 / 1000

Fig. 87: Oil Pan, Upper Gasket, Bolts & Engine Block
Courtesy of GENERAL MOTORS CORP.

3. Pre-assemble the oil pan gasket to the pan, upper.

1. Install the gasket onto the oil pan, upper.

2. Install the oil pan bolts to the pan and through the gasket.

4. Install the oil pan, upper, gasket and bolts to the engine block.

5. Tighten bolts finger tight. Do not overtighten.

6. Place a straight edge across the rear of the engine block and the rear of the oil pan at the transmission

housing mounting surfaces.

IMPORTANT: Be sure to align the oil gallery passages in the oil pan and engine block

properly with the oil pan gasket.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 3 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:06:38 AM

Page 101

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands