Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 304 / 1000

6. Remove the used crankshaft balancer bolt.

7. Measure for a correctly installer balancer.

If the balancer is not installed to the proper dimensions, install the

J 41665

and repeat the installation

procedure.

Fig. 188: Identifying Harmonic Balancer Bolt

Courtesy of GENERAL MOTORS CORP.

8. Install the NEW crankshaft balancer bolt.

Tighten:

IMPORTANT: The nose of the crankshaft should be recessed 2.40-4.48 mm (0.094-0.176

in) into the balancer bore.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:41 AM

Page 204

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands