Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 215

Page: 215 / 1000

Fig. 109: AIR Pipe Gasket, Exhaust Manifold & Bolts

Courtesy of GENERAL MOTORS CORP.

5. Loosen, DO NOT remove the AIR pipe bolt at the rear of the left cylinder head.

6. Slide the AIR pipe up and out from behind the bolt.

7. Reposition the AIR pipe.

8. Remove the AIR pipe gasket from the exhaust manifold.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:37 AM

Page 115

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands