Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 909

Page: 909 / 1000

1. Lubricate the outer edge of the oil seal (140) with clean engine oil.

2. Lubricate the front cover oil seal bore with clean engine oil.

Fig. 84: View Of J 41478

Courtesy of GENERAL MOTORS CORP.

3. Install the crankshaft front oil seal onto the

J 41478

guide.

4. Install the

J 41478

threaded rod, with nut, washer, guide, and oil seal, into the end of the crankshaft.

5. Use the

J 41478

in order to install the oil seal into the cover bore.

1. Use a wrench and hold the hex on the installer bolt.

2. Use a second wrench and rotate the installer nut clockwise until the seal bottoms in the cover bore.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 3 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:06:38 AM

Page 96

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands