Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 635

Page: 635 / 1000

Tighten:

1. Tighten the connecting rod bolts first pass to 20 N.m (15 lb ft).

2. Tighten the connecting rod bolts final pass to 75 degrees using the

J 45059

4. Remove the bearing cap, bearing, and bolts.

Fig. 114: Measuring The Gaging Plastic On Crankshaft

Courtesy of GENERAL MOTORS CORP.

5. Measure the gaging plastic at its widest area using the scale supplied with the plastic gaging kit. Refer to

Engine Mechanical Specifications (LS1)

Engine Mechanical Specifications (LS6)

Measuring Connecting Rod Bearing Clearance - Using J 43690/J 43690-100

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:03:14 AM

Page 119

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands