Chevrolet 5.7L Corvette 2004 Shop Manual Download

Page: 112 / 1000

Fig. 12: A/C Drive Belt Tensioner

Courtesy of GENERAL MOTORS CORP.

1. Install the A/C drive belt tensioner.

2. Tighten the A/C drive belt tensioner bolt.

Tighten:

Tighten the A/C drive belt tensioner bolt to 50 N.m (37 lb ft).

3. Lower the vehicle.

4. Install the A/C drive belt. Refer to

Drive Belt Replacement - Air Conditioning

NOTE:

Refer to Fastener Notice in Cautions and Notices.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:32 AM

Page 12

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Related manuals for 5.7L Corvette 2004

Brands by name

Popular brands