manualshive.com logo in svg

Chevrolet 5.7L Corvette 2004, Shop Manual

Share
Download
Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 499

Fig. 373: J 42386-A, Crankshaft Balancer & Bolt

 

Courtesy of GENERAL MOTORS CORP.

 

NOTE:

Refer to Fastener Notice in Cautions and Notices.

IMPORTANT:

z

For manual transmission applications, note the position of the 
crankshaft balancer before removal. The balancer does not use a 
key or keyway for positioning. Mark or scribe the end of the 
crankshaft and the balancer before component removal. The 
crankshaft balancer must be installed to the original position. If 
replacing the crankshaft balancer, note the location of any existing 
balance weights, if applicable. Install new balance weights into the 

 

2004 Chevrolet Corvette 

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

  

Helpmelearn 

 

December-24-07 10:58:53 AM

Page 399 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands