Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 595

Page: 595 / 1000

Tools Required

J 41712 Oil Pressure Switch Socket

Fig. 77: Remove J 41712 Oil Pressure Sensor

Courtesy of GENERAL MOTORS CORP.

IMPORTANT:

Do not remove the engine block front oil gallery plug unless service
is required.

If the front oil gallery plug is removed for service, a NEW oil gallery
plug must be installed.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 2 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:03:12 AM

Page 79

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands