Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 152

Page: 152 / 1000

Fig. 47: TP Sensor Harness Clip & PCV Tube

Courtesy of GENERAL MOTORS CORP.

25. Remove the TP sensor harness clip from the positive crankcase ventilation (PCV) tube.

26. Remove the PCV tube from the right rocker arm cover and throttle body.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:34 AM

Page 52

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands