Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 110

Page: 110 / 1000

Fig. 10: Accessory Drive Belt Tensioner & Bolts

Courtesy of GENERAL MOTORS CORP.

1. Install the accessory drive belt tensioner.

2. Install the accessory drive belt tensioner bolts.

Tighten:

Tighten the accessory drive belt tensioner bolts to 50 N.m (37 lb ft) starting with the lower bolt

first.

3. Install the accessory drive belt. Refer to

Drive Belt Replacement - Accessory

DRIVE BELT TENSIONER REPLACEMENT - AIR CONDITIONING

Removal Procedure

NOTE:

Refer to Fastener Notice in Cautions and Notices.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:32 AM

Page 10

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands