Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 896

Page: 896 / 1000

Fig. 75: View Of J 41480 & J 41476 Installed

Courtesy of GENERAL MOTORS CORP.

6. Install the

J 41476

and bolts onto the rear of the crankshaft.

Tighten:

1. Tighten the tool mounting bolts until snug. Do not overtighten.

2. Tighten the

J 41480

tool-to-rear cover bolts evenly to 12 N.m (106 lb in).

3. Tighten the rear cover bolts to 25 N.m (18 lb ft).

IMPORTANT: The tapered legs of the alignment tool must enter the rear cover oil seal

bore.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 3 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:06:37 AM

Page 83

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands