Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 941

Page: 941 / 1000

VALVE ROCKER ARM AND PUSH ROD INSTALLATION

Fig. 112: View Of Valve Rocker Arm Pivot Support

Courtesy of GENERAL MOTORS CORP.

1. Lubricate the valve rocker arms and pushrods with clean engine oil.

2. Lubricate the flange of the valve rocker arm bolts with clean engine oil.

Lubricate the flange or washer surface of the bolt that will contact the valve rocker arm.

IMPORTANT:

When using the valve train components again, always install the
components to the original location and position.

Valve lash is net build, no valve adjustment is required.

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 3 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:06:39 AM

Page 128

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands