Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 311

Page: 311 / 1000

Courtesy of GENERAL MOTORS CORP.

1. Remove the crankshaft balancer. Refer to

Crankshaft Balancer Replacement

2. Remove the water pump. Refer to

Water Pump Replacement

in Engine Cooling.

3. Remove the oil pan-to-front cover bolts (2).

Fig. 195: Front Cover Gasket & Bolts

Courtesy of GENERAL MOTORS CORP.

4. Remove the front cover bolts.

5. Remove the front cover and gasket.

6. Discard the front cover gasket.

7. Clean and inspect the engine front cover. Refer to

Engine Front Cover Cleaning and Inspection

Installation Procedure

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 1 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 10:58:41 AM

Page 211

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands