Chevrolet 5.7L Corvette 2004 Shop Manual Download Page 954

Page: 954 / 1000

Fig. 124: Ignition Coil Bracket Bolts & Rocker Cover

Courtesy of GENERAL MOTORS CORP.

8. Apply threadlock GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the threads of the

bracket bolts.

9. Install the ignition coils and bracket assembly and bolts to the rocker cover.

Tighten:

Tighten the ignition coil bracket bolts to 12 N.m (106 lb in).

2004 Chevrolet Corvette

2004 ENGINE PERFORMANCE Engine Mechanical (Repair Instructions 3 Of 3) - 5.7L - Corvette

Helpmelearn

December-24-07 11:06:40 AM

Page 141

Summary of Contents for 5.7L Corvette 2004









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands

Chevrolet 5.7L Corvette 2004, Shop Manual

Search results

Summary of Contents for 5.7L Corvette 2004

Reviews:

Brands by name

Popular brands